Code: 4540 A fast drying, non toxic, low VOC, water based, clear urethane for interior timber. Can be tinted to Quantum’s large range of Transparent or Solid Opaque Stain Colours. Features: Environmentally responsible – made from bio based, ecologically sustainable products Non-toxic, low odour Fast drying with only one hour recoat time, apply multiple coats in a day Smooth flow, self – levelling finish Low yellowing – added UV stabilisers May be tinted with Quantum transparent or solid opaque stains to provide extra life due to added UV protection Colour : Clear or tinted with Quantum Transparent and Solid Opaque Stains Gloss : Matt, Satin or Gloss VOC : <46 g per litre – Refer to VOC certificate for more information.VOC is dependent on gloss level Coverage : 10-15m² per litre. First coat may use more. (Coverage is dependent upon the porosity of the substrate) Thinning : Up to 5% with water or Quantum Wet Edge Extender to help mainatin a wet edge and reduce drag on hot days Drying : Touch Dry : 30 minutes. Recoat : 1 hour. Full hardness and cure may take up to 7 days. (In cooler or humid conditions drying times will be longer. Drying time is affected by wet film thickness (WFT), the higher the WFT the slower the rate of reaction and the longer dry time. Clean Up : Water Packaging : 1L, 4L & 10L To View Tech Data Sheet and Safety Data Sheet: Register To View Preparation : Good preparation is key to a professional looking, long lasting finish. Precaution :  Always test recycled timber for adhesion prior to full application. MICROCLEAR is best used in semi shaded areas. Tools : Brush, roller (short nap) or spray application. Application : Refer to Technical Datasheet for full application method. Ensure the surface is clean, dry and free from all dirt, dust, grease and grime. Sanding not usually required, however if grain raising occurs de-nib / lightly sand after the first coat. Interior : Apply 1 to 3 coats to achieve the desired finish. Exterior : Apply a minimum of 3 coats. Spraying: Airless spray recommended. Use a 0.33 to 0.38mm (13 – 15 thou) orifice, 10cm fan (dependent on job) with a regulated pump pressure of 350-400 kPa (50 – 55 psi) tip pressure. Back brushing is recommended to achieve an even finish. Use normal protection i.e. mask, overalls. Watch your overspray. Wash off with soap and water before it dries. Interior Timber such as furniture, doors, windows, cupboards, storage units and skirting boards. Read More

Code: 4300 A transparent interior wiping stain for brush or cloth application. Topcoat with MICROCLEAR, TIMBRE PLUS Interior or MICROFLOOR. Features: Suitable to stain all interior timber Wide range of Transparent tint colours available Overcoat with TIMBRE PLUS Interior, MICROCLEAR or MICROFLOOR Colour : Refer to Quantum Transparent Stain Board Gloss : N/A VOC : <45g per litre Coverage : 12m² per litre on dressed timber & approximately 6m² per litre on rough sawn timber Drying : Touch Dry : 1 hour. Recoat : 2 hours ( In cooler or humid drying times will be longer. Avoid exposure to steam and condenstaion for 48 hours after painting. Avoid washing the substrate for a week). Clean Up : Water Packaging : 500ml, 1L, 4L & 10L To View Tech Data Sheet and Safety Data Sheet: Register To View Preparation : Good preparation is key to a professional looking, long lasting finish Mixing :  Stir thoroughly before use. (Note: Stirring the stain well before application is essential to ensure to correct colour and even application. If you are using more than one can, you should mix the can contents together before application to achieve consistent colour. Test the colour on a small section first to ensure it is what you expect). Tools : Brush or cloth application Application: Sand where necessary to improve imperfections. Ensure the surface is clean, dry and free from all dirt, dust, grease and grime. Apply AQUASTAIN evenly with either a brush or a cloth, allow to dry. Finish with two coats of either TIMBRE PLUS Interior, MICROCLEAR or MICROFLOOR. Interior timber that has not been previously painted with a solid paint. Not recommended for previously stained or painted surfaces unless completely stripped and cleaned. Read More