Code: 5202 Cobalt accelerator for use with MIROPOL Polyester undercoats. To View Tech Data Sheet and Safety Data Sheet: Register To View Read More

Code: 5130 A high build, white polyester undercoat for MDF and particleboard. It is easy to sand and is designed to be top coated with MIROTHANE PU polyurethane topcoats. Features: Easy to sand, will powder easily ensuring quick sanding Excellent vertical hold up Excellent flow Excellent build, it will enhance the finished appearance of the topcoat by filling and covering the fibres of the substrate Specifications: Colour : White Specific Gravity : 1.45 +/-0.05 Build : Excellent Sandability : Excellent Vertical Hold Up : Good Solvent Resistance : Very Good Water Resistance : Very Good Levelling & Flow : Very Good Sink Back : Minimal Coverage : 3m2 per litre at 300 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1208 or 1234 Thinner. To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio : Mix by volume, 1 Litre 5130 Part A + 20ml 5202 Accelerator + 10ml Peroxide (MEKP Catalyst) (100:2:1) Always mix 5202 Accelerator into the 5130 Part A base before adding the peroxide (MEKP Catalyst). Mixing the Accelerator and the Peroxide Hardener together may cause an explosion or fire. Pot Life : Approximately 45 minutes at 25°C. Pot life varies significantly with ambient temperature and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Refer to the MIROPOL PE Polyester Product Information Guide for mixing ratios to extend pot life. Thinning : Up to 30% with MIROSOL 1208, 1234 or 1224 Thinner. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Interior doors, kitchen & bathroom cabinets, commercial joinery and wall panelling and domestic furniture Read More

Code: 5007 A high build, isocyanate free, two pack polyester, clear coating. MIROPOL 5007 Clear has a very hard, high gloss clear topcoat finish to provide a “glass like” appearance. Features: High Build Very High Gloss MIROPOL 5007 Clear can be applied to both natural timber substrates or foil covered MDF board. For interior use only. Specifications: Colour : Clear Finish : Full Gloss Build : Excellent Sandability : Good Vertical Hold Up : Good Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 8m2 per litre at 100-150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1215 Thinner Packaging : 20L To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Mix 1 part by volume MIROPOL 5007 Clear Topcoat to 1 part by volume MIROPOL 5007 "B" Solution and stir thoroughly. Pot Life : 2-3 hours (mix only samll quantities at any one time). Thinning : Not required as MIROPOL 5007 Clear us supplied ready for ysue (RFU). If required use MIROSOL 1234 Ultra Fast Thinner sparingly. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use. Solid and veneer timber fixtures and furniture. Restaurant, bar, and hotel furniture. Piano's. Funeral caskets and shop fittings Read More