MIROTHANE PU Polyurethane Coatings

Mirotone’s range of clear and pigmented two pack polyurethane coatings are ideal for use on high quality fixtures and furniture. Easy to use and available in a range of gloss levels, Mirotone has the right system to meet your requirements. Typical applications include internal doors, kitchen cabinets, commercial joinery / wall panelling, domesticand commercial furniture. Premium systems available for bar & kitchen bench tops and marine fit outs.

 

Filter
Categories
Type
Gloss Level
Colour Type
Product
MIROTHANE PU 5650 Pigmented Topcoat
MIROTHANE PU 5650 Pigmented Topcoat-image
A premium, two pack, fast cure polyurethane topcoat that has been formulated to have superior resistance to water, general household contaminants, marring and scuffing. Available in a full range of gloss levels. Features: 
  • Available in an extensive colour range or tintable to a colour sample
  • Excellent flow and levelling results in a smooth even finish
  • With the application of the recommended undercoat or primer may be applied over wood, MDF, melamine, glass, metal and plastic
Specifications: Colour : White & Tinted Colours Finish : Satin (30%), Semi Gloss (60%) & Full Gloss Build : Very Good Sandability : Good Vertical Hold Up : Good Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 8m2 per litre at 125 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner Packaging : 1-16L To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Refer to Technical Data Sheet. Pot Life : Satin & Semi Gloss: > 8 hours Full Gloss: 2 – 8 hours Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Satin & Semi Gloss – Thin 40-55% with MIROSOL 1217 (Fast), 1263 (Medium), 1266, 1218 (Slow) when using high solids Part B. When using Ready For Use (RFU) Part B’s thin 30-40%. Full Gloss – thin up to 25% with MIROSOL 1263 (Medium), 1260, 1266, 1218 (Slow) when using high solids Part B. When using RFU Part B’s thin 20-30%. MIROSOL 1281 Matt Promoter may be added to MIROTHANE PU 5650 Satin at an addition rate of 30-40% to achieve an approximate gloss level of 10-15%. In order to maintain consistency of colour and gloss during a job or repeat jobs of the same colour, it is critical to use the same Part B Hardener and thinner throughout. To speed up dry time add up to 3% MIROTHANE PU 5795 Accelerator. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use. Interior doors, kitchen & bathroom cabinets, commercial joinery and wall panelling and domestic furniture. With the appropriate primers may be used to topcoat glass, plastic and metal.
Type: Topcoat
Gloss Level:
Colour Type: White, Tinted
MIROTHANE PU 5608 Pigmented Topcoat
MIROTHANE PU 5608 Pigmented Topcoat-image

Code: 5608

MIROTHANE PU 5608 is an economical, user friendly, two pack pigmented polyurethane topcoat for quality furniture and fittings.
Features:
  • Excellent flow, high build and quick drying
  • Economical, cost effective furniture grade polyurethane
Specifications: Colour : White, full colour range Finish : Matt (10%), Satin (30%) & Semi-Gloss (60%) Build : Very Good Sandability : Very Good Vertical Hold Up : Excellent Solvent Resistance : Very Good Water Resistance : Very Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1215 or 1217 Thinner Packaging : 1, 4 & 16L To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Refer to Technical Data Sheet. Pot Life : 6-8 hours at 25°C (Refer to Technical Datas Sheet). Thinning : Thin 20-40% with MIROSOL 1280 (fast), 1265 (medium), 1266 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Domestic furniture, commercial joinery, kitchen and bathroom cabinetry.  
Type: Topcoat
Gloss Level:
Colour Type: White & Colours
MIROTHANE PU 5610 Pigmented Topcoat
MIROTHANE PU 5610 Pigmented Topcoat-image

Code: 5610

High performance, two pack, acrylic modified polyurethane coating. MIROTHANE PU 5610 has superior adhesion over a wide variety of substrates.
Features:
  • Outstanding durability, gloss and colour retention
  • Excellent opacity, achieve a high gloss finish with minimal coats
Specifications: Colour : White and Tinted Colours Finish : Gloss Build : Good Sandability : Good Vertical Hold Up : Good Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner

To View Tech Data Sheet and Safety Data Sheet: Register To View

Application: Mix Ratio (by volume) : 4 Parts 5610 Part A + 1 Part 5789 Part B (4A: 1B). Pot Life : Up to 10 hours Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : 25-40% with MIROSOL 1266 (fast), 1260 (Medium), 1218 (Slow) thinner. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Petrochemical industry, road tankers, tank farms, marine environment, concrete mixing bowls, trailers, horse floats, truck chassis, automotive, CFC toilet partitions.
Type: Topcoat
Gloss Level:
Colour Type: White, Tinted
MIROTHANE PU 5588 Clear Topcoat
MIROTHANE PU 5588 Clear Topcoat-image

Code: 5588

User friendly, easy to apply, clear polyurethane topcoat. Excellent flow and quick drying ensures an excellent finish and increased throughput.
Features:
  • Can be applied over a range of sealers including MIROCAT PC 3241 and MIROCAT PC 3242 Preact Sealers and MIROTHANE PU 5533 and MIROTHANE PU 5545 Polyurethane
  • Excellent flow and levelling
  • Economical – a cost effective furniture grade polyurethane topcoat
Specifications: Colour : Clear Finish : Satin (30%) and Satin (20%) Build : Very Good Sandability : Very Good Vertical Hold Up : Good Solvent Resistance : Very Good Water Resistance : Very Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : 4 Parts 5588 Part A + 1 Part 5747 Part B (4A:1B) or 10 Parts 5588 Part A + 1 Part 5715, 5728, 5735 or 5757 (10A:1B) Pot Life : 4-6 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin 20-40% with MIROSOL 1217 (Fast), 1263 (Medium), 1266 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Domestic furniture, commercial joinery and kitchen cabinets
Type: Topcoat
Gloss Level:
Colour Type: Clear
MIROTHANE PU 5578 Clear Natural Topcoat
MIROTHANE PU 5578 Clear Natural Topcoat-image

Code: 5578

High performance, fast drying, clear, two pack, non-yellowing, acrylic polyurethane for interior wood and wood composites. It has a natural matt finish and has outstanding durability, flexibility and colour stability.
Features:
  • Contains UV absorbers and light stabilisers that have been proven highly effective in protecting reconstituted, dyed and natural wood veneers from colour change when exposed to ultraviolet (UV) light
  • Low gloss is resistant to unsightly oily fingerprints. Fingerprints can be easily removed with a clean lint free cloth without leaving residual glossy spots, particularly important when applying a clear matt topcoat over a dark base
  • Fast drying
  • Mould resistant – under normal atmospheric conditions. (i.e. article is kept in a properly ventilated room by either open windows or used in a room with air extractor fans)
Specifications: Colour : Clear Finish : 5% and 20% Build : Good Sandability : Good Solvent Resistance : Very Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Matt & Satin: 5 Parts 5578 Part A + 1 Part 5735 Part B (5A:1B), MIROTHANE PU 5747 may also be used in Matt. Pot Life : Up to 24 hours at 25°C Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin 30% with MIROSOL 1217 (Fast), 1266 (Slow), 1218 (Ultra Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior: Reconstituted, dyed and natural wood veneers, joinery, kitchen cupboards, wardrobes, wall panelling, furniture-table topcoat, bench tops, commercial furniture and fit-outs, window furnishings and blinds.
Type: Topcoat
Gloss Level:
Colour Type: Clear
MIROTHANE PU 5577 Sun Shield Clear Topcoat
MIROTHANE PU 5577 Sun Shield Clear Topcoat-image

Code: 5577

High-performance, clear, two-pack, non-yellowing, acrylic polyurethane for interior wood & wood composites. MIROTHANE PU 5577 Sun-Shield contains a sophisticated package of UV absorbers and light stabilisers that have been proven highly effective in protecting reconstituted, dyed and natural wood veneers from colour change when exposed to ultraviolet (UV) light.
Features:
  • Contains UV absorbers and light stabilisers that have been proven highly effective in protecting reconstituted, dyes and natural wood veneers from colour change when exposed to ultraviolet (UV) light.
  • High solids means less coats are required to achieve a full finish
  • Subdued gloss is highly resistant to unsightly oily finger prints. Fingerprints can be easily removed with a clean rag without leaving residual gloss spots, particularly important when applying a clear matt topcoat over a dark base
  • Available in a full range of gloss levels; matt, satin, semi-gloss and full gloss
Specifications: Colour : Clear Finish : Matt (10%), Satin (30%), Semi Gloss (60%) & Full Gloss Build : Very Good Sandability : Good Vertical Hold Up : Good Solvent Resistance : Very Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1208 or 1234 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Matt & Satin: 4 Parts 5577 Part A + 1 Part 5735 Part B (4A:1B) Full Gloss: 4 Parts 5577 Part A + 1 Part 5757 or 5789 (4A:1B) Pot Life : Up to 8 hours at 25°C Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Matt & Satin: Thin 40-60% with MIROSOL 1217 (Fast), 1263 (Medium), 1266 (Slow), 1218 (Ultra Slow) Full Gloss: Thin up to 15% with MIROSOL 1263 (Medium), 1266 or 1260 (Slow), 1218 (Ultra Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior: Reconstituted, dyed and natural wood veneers, kitchen cupboards, wall panelling, table topcoat, bench tops, commercial furniture and fit-outs, window furnishings and blinds, children’s toys. Semi Exterior: Covered entry doors and internal faces of opening windows. Exterior: When used as a protective clear topcoat over an exterior grade pigmented basecoat e.g. MIROTHANE PU 5610 polyurethane on metal, plastic or over appropriately primed carbon fibre.
Type: Topcoat
Gloss Level: matt, satin, semi-gloss and full gloss
Colour Type: Clear
MIROTHANE PU 5555 Clear Topcoat
MIROTHANE PU 5555 Clear Topcoat-image

Code: 5555

Premium, two pack, clear polyurethane. High clarity results in striking grain definition and enhances the natural beauty of stained timber.
Features:
  • Excellent water and chemical resistance makes it ideal for demanding in-service environment  such as marine fit-outs, bench tops and bar tops
  • Very low yellowing, it is suitable for use over light coloured wood and veneers when mixed with a low yellowing MIROTHANE PU Part B Hardener
  • The full gloss version results in a brilliant high gloss finish with excellent distinction of image (DOI).
  • Available in satin, semi gloss and full gloss
Specifications: Colour : Clear Finish : Satin (30%), Semi Gloss (60%) & Full Gloss Build : Very Good Sandability : Excellent Vertical Hold Up : Good: Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner

To View Tech Data Sheet and Safety Data Sheet: Register To View

Application: Mixing Ratio (by volume) : Refer to datasheet for mixing ratios Pot Life : 2-3 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Refer to datasheet for thinning Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for demanding environments such as bar, kitchen bench tops, bathroom vanities, interior marine fit-outs and commercial fit outs.
Type: Topcoat
Gloss Level:
Colour Type: Clear
MIROTHANE PU 5545 Clear Sealer
MIROTHANE PU 5545 Clear Sealer-image

Code: 5545

Premium, two pack, clear, polyurethane sealer that provides an excellent sanding base for clear polyurethane topcoats.
Features:
  • Good build enhances the final finish by sealing, filling and covering the fibres of the the substrate
  • Excellent flow and levelling
  • Easy sanding ensures time to sand and the best possible surface tor topcoating
  • Low yellowing, suitable over light coloured wood/veneers and liming stains when mixed with one of the low yellowing MIROTHANE Part B Hardeners
Specifications: Colour : Milky in can dries clear Build : Very Good Sandability : Excellent Vertical Hold Up : Good Solvent Resistance : Very Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : 2 Parts 5545 Part A + 1 Part 5747 Part B (2A:1B) or 4 Parts 5545 Part A + 1 Part 5715, 5728, 5735 or 5757 (4A:1B) Pot Life : 2-3 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin 10-20% with MIROSOL 1217 (Fast), 1263 (Medium), 1266 or 1218 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Commercial joinery, wall panelling, domestic furniture, high rise office and hotel fit outs and interior marine fit-outs.
Type: Sealer
Gloss Level:
Colour Type:
MIROTHANE PU 5789 Ultra Flex High Solids Hardener
MIROTHANE PU 5789 Ultra Flex High Solids Hardener-image

Code: 5789

To View Tech Data Sheet and Safety Data Sheet: Register To View
Type: Catalysts & PU Hardeners
Gloss Level:
Colour Type:
MIROTHANE PU 5780 Slow Hardener
MIROTHANE PU 5780 Slow Hardener-image

Code: 5780

To View Tech Data Sheet and Safety Data Sheet: Register To View
Type: Catalysts & PU Hardeners
Gloss Level:
Colour Type:
MIROTHANE PU 5757 Medium High Solids Hardener
MIROTHANE PU 5757 Medium High Solids Hardener-image

Code: 5757

To View Tech Data Sheet and Safety Data Sheet: Register To View
Type: Catalysts & PU Hardeners
Gloss Level:
Colour Type:
MIROTHANE PU 5747 Fast Hardener
MIROTHANE PU 5747 Fast Hardener-image

Code: 5747

To View Tech Data Sheet and Safety Data Sheet: Register To View
Type: Catalysts & PU Hardeners
Gloss Level:
Colour Type:
MIROTHANE PU 5735 Fast/Med High Solids Hardener
MIROTHANE PU 5735 Fast/Med High Solids Hardener-image

Code: 5735

To View Tech Data Sheet and Safety Data Sheet: Register To View
Type: Catalysts & PU Hardeners
Gloss Level:
Colour Type:
MIROTHANE PU 5728 Fast Cure High Solids Hardener
MIROTHANE PU 5728 Fast Cure High Solids Hardener-image

Code: 5728

To View Tech Data Sheet and Safety Data Sheet: Register To View
Type: Catalysts & PU Hardeners
Gloss Level:
Colour Type:
MIROTHANE PU 5718 Vert Fast HS Hardener
MIROTHANE PU 5718 Vert Fast HS Hardener-image

Code: 5718

Type: Catalysts & PU Hardeners
Gloss Level:
Colour Type:
MIROTHANE PU 5535 Clear Sealer
MIROTHANE PU 5535 Clear Sealer-image

Code: 5535

A two pack, clear, polyurethane sanding sealer typically used under MIROPOL PE 5007 High Gloss Clear Top Coat on timber, veneer or foil covered MDF board to provide a high-gloss, wet look finish.
Features:
  • Fast drying and easy sanding
  • Excellent flow & levelling
  • Highlights the grain and colour of Rimu
  • Can be used under any Mirotone clear topcoat
Specifications: Build: Very Good Sandability: Very Good Vertical Hold Up: Excellent Solvent Resistance: Very Good Water Resistance: Excellent Levelling & Flow: Excellent Sink Back: Minimal Colour: Milky in-can dries clear To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio: 2 Parts 5535 Part A + 1 Part 5730 Part B Pot Life: 3-4 hours at 25ºC   (Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning: Not normally required but can be thinned up to 5% with MIROSOL 1217 Fast Thinner if required. Suction Gun: Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot: Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400 kpa (50-55 psi) and a pot pressure of 45 kpa (6psi) max. Airless Spray - Use 0.23 to 0.33 (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400 kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90 kpa (10-15psi). Where To Use: Interior use only for example solid and veneer timber fixtures and furniture including restaurant, bar and hotel furniture, pianos and caskets.
Type: Sealer
Gloss Level:
Colour Type: Clear
MIROTHANE PU 5500 Isolator
MIROTHANE PU 5500 Isolator-image

Code: 5500

Versatile clear isolator that minimises the risk of resin exudation and tannin bleed on timber and minimises the risk of edge cracking on MDF.
Features:
  • Fast drying
  • No sanding required
  • Water white, excellent clarity
  • Excellent adhesion to wood, MDF & LPM
Specifications: Colour : Clear Build : Low Vertical Hold Up : Good Solvent Resistance : Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 10m2 per litre at 100 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : When used as a two pack mix 10 Parts 5500 Part A + 1 Part 5789 (10A:1B). Pot Life : 4 hours at 25°C Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin single pack 20-30% and two pack 12-25% with MIROSOL 1217 (Fast), 1263 (Medium), 1266 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Tannin blocking primer under MIROTEC WB water based coatings, mouldings, picture frames, MDF furniture and fixtures, MDF routed grooves and solid Jarrah furniture and articles.
Type: Sealer
Gloss Level:
Colour Type: Clear
MIROTHANE PU 5631 White Undercoat
MIROTHANE PU 5631 White Undercoat-image

Code: 5631

Premium, high build, two pack polyurethane undercoat.
Features:
  • Fast drying, ideal for automatic lines with in-line or early forced drying
  • Easy to sand, powders easily making it ideal for hand sanding
  • Has a slight sheen making it easier to see where it has been sanded
  • Low sink back, produces and excellent high gloss finish when topcoated with one of Mirotone’s full gloss polyurethane topcoats, comparable with the gloss achieved with a polyester undercoat
  • Excellent vertical hold up
Specifications: Colour : White & Tinted Finish : Slight sheen Build : Very High Sandability : Excellent Vertical Hold Up : Excellent Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated. Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner

To View Tech Data Sheet and Safety Data Sheet: Register To View

Application: Mixing Ratio (by volume) : 2 Parts 5631 Part A + 1 Part 5747 Part B (2A:1B) or 4 Parts 5631 Part A + 1 Part 5728 or 5735 (4A:1B) Pot Life : 2 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin up to 40% with MIROSOL 1217 (Fast), 1263 (Medium) or 1218, 1266 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use. Interior doors, kitchen & bathroom cabinets, commercial joinery, wall panelling and domestic furniture.
Type: Undercoat
Gloss Level:
Colour Type: White, Tinted
MIROTHANE PU 5626 White Undercoat
MIROTHANE PU 5626 White Undercoat-image

Code: 5626

Premium grade, high solids, low viscosity two pack polyurethane undercoat. Very easy to sand and provides excellent DOI (Distinction of Image) when topcoated with a MIROTHANE PU topcoat gloss.
Features:
  • Easy to sand, powders easily making it ideal for hand sanding
  • High solids, low viscosity provides superior build with minimal thinning. Excellent for sealing the fibres of MDF.
  • Superior chemical and moisture resistance
  • Use up excess MIROTHANE PU 5650  topcoat by adding it into MIROTHANE PU 5626 to create your own tinted undercoat
Specifications: Colour : White, Black & Tinted Build : Very High Sandability : Excellent Vertical Hold Up : Excellent Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ration (by volume) : 3 Parts 5626 Part A + 1 Part 5747 Part B (3A:1B) or 5 Parts 5626 Part A + 1 Part 5715, 5728 or 5735 (5A:1B) Pot Life : 2 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin up to 20% with MIROSOL 1217 (Fast), 1263 (Medium), 1218, 1266 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use. Doors, kitchen & bathroom cabinets, commercial joinery and wall panelling and domestic furniture.
Type: Undercoat
Gloss Level:
Colour Type: White, Black & Tinted
MIROTHANE PU 5650 Pigmented Topcoat-image
MIROTHANE PU 5650 Pigmented Topcoat
A premium, two pack, fast cure polyurethane topcoat that has been formulated to have superior resistance to water, general household contaminants, marring and scuffing. Available in a full range of gloss levels. Features:  Available in an extensive colour range or tintable to a colour sample Excellent flow and levelling results in a smooth even finish With the application of the recommended undercoat or primer may be applied over wood, MDF, melamine, glass, metal and plastic Specifications: Colour : White & Tinted Colours Finish : Satin (30%), Semi Gloss (60%) & Full Gloss Build : Very Good Sandability : Good Vertical Hold Up : Good Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 8m2 per litre at 125 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner Packaging : 1-16L To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Refer to Technical Data Sheet. Pot Life : Satin & Semi Gloss: > 8 hours Full Gloss: 2 – 8 hours Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Satin & Semi Gloss – Thin 40-55% with MIROSOL 1217 (Fast), 1263 (Medium), 1266, 1218 (Slow) when using high solids Part B. When using Ready For Use (RFU) Part B’s thin 30-40%. Full Gloss – thin up to 25% with MIROSOL 1263 (Medium), 1260, 1266, 1218 (Slow) when using high solids Part B. When using RFU Part B’s thin 20-30%. MIROSOL 1281 Matt Promoter may be added to MIROTHANE PU 5650 Satin at an addition rate of 30-40% to achieve an approximate gloss level of 10-15%. In order to maintain consistency of colour and gloss during a job or repeat jobs of the same colour, it is critical to use the same Part B Hardener and thinner throughout. To speed up dry time add up to 3% MIROTHANE PU 5795 Accelerator. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use. Interior doors, kitchen & bathroom cabinets, commercial joinery and wall panelling and domestic furniture. With the appropriate primers may be used to topcoat glass, plastic and metal. Read More
MIROTHANE PU 5608 Pigmented Topcoat-image
MIROTHANE PU 5608 Pigmented Topcoat
Code: 5608 MIROTHANE PU 5608 is an economical, user friendly, two pack pigmented polyurethane topcoat for quality furniture and fittings. Features: Excellent flow, high build and quick drying Economical, cost effective furniture grade polyurethane Specifications: Colour : White, full colour range Finish : Matt (10%), Satin (30%) & Semi-Gloss (60%) Build : Very Good Sandability : Very Good Vertical Hold Up : Excellent Solvent Resistance : Very Good Water Resistance : Very Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1215 or 1217 Thinner Packaging : 1, 4 & 16L To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Refer to Technical Data Sheet. Pot Life : 6-8 hours at 25°C (Refer to Technical Datas Sheet). Thinning : Thin 20-40% with MIROSOL 1280 (fast), 1265 (medium), 1266 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Domestic furniture, commercial joinery, kitchen and bathroom cabinetry.   Read More
MIROTHANE PU 5610 Pigmented Topcoat-image
MIROTHANE PU 5610 Pigmented Topcoat
Code: 5610 High performance, two pack, acrylic modified polyurethane coating. MIROTHANE PU 5610 has superior adhesion over a wide variety of substrates. Features: Outstanding durability, gloss and colour retention Excellent opacity, achieve a high gloss finish with minimal coats Specifications: Colour : White and Tinted Colours Finish : Gloss Build : Good Sandability : Good Vertical Hold Up : Good Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mix Ratio (by volume) : 4 Parts 5610 Part A + 1 Part 5789 Part B (4A: 1B). Pot Life : Up to 10 hours Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : 25-40% with MIROSOL 1266 (fast), 1260 (Medium), 1218 (Slow) thinner. Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Petrochemical industry, road tankers, tank farms, marine environment, concrete mixing bowls, trailers, horse floats, truck chassis, automotive, CFC toilet partitions. Read More
MIROTHANE PU 5588 Clear Topcoat-image
MIROTHANE PU 5588 Clear Topcoat
Code: 5588 User friendly, easy to apply, clear polyurethane topcoat. Excellent flow and quick drying ensures an excellent finish and increased throughput. Features: Can be applied over a range of sealers including MIROCAT PC 3241 and MIROCAT PC 3242 Preact Sealers and MIROTHANE PU 5533 and MIROTHANE PU 5545 Polyurethane Excellent flow and levelling Economical – a cost effective furniture grade polyurethane topcoat Specifications: Colour : Clear Finish : Satin (30%) and Satin (20%) Build : Very Good Sandability : Very Good Vertical Hold Up : Good Solvent Resistance : Very Good Water Resistance : Very Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : 4 Parts 5588 Part A + 1 Part 5747 Part B (4A:1B) or 10 Parts 5588 Part A + 1 Part 5715, 5728, 5735 or 5757 (10A:1B) Pot Life : 4-6 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin 20-40% with MIROSOL 1217 (Fast), 1263 (Medium), 1266 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Domestic furniture, commercial joinery and kitchen cabinets Read More
MIROTHANE PU 5578 Clear Natural Topcoat-image
MIROTHANE PU 5578 Clear Natural Topcoat
Code: 5578 High performance, fast drying, clear, two pack, non-yellowing, acrylic polyurethane for interior wood and wood composites. It has a natural matt finish and has outstanding durability, flexibility and colour stability. Features: Contains UV absorbers and light stabilisers that have been proven highly effective in protecting reconstituted, dyed and natural wood veneers from colour change when exposed to ultraviolet (UV) light Low gloss is resistant to unsightly oily fingerprints. Fingerprints can be easily removed with a clean lint free cloth without leaving residual glossy spots, particularly important when applying a clear matt topcoat over a dark base Fast drying Mould resistant – under normal atmospheric conditions. (i.e. article is kept in a properly ventilated room by either open windows or used in a room with air extractor fans) Specifications: Colour : Clear Finish : 5% and 20% Build : Good Sandability : Good Solvent Resistance : Very Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Matt & Satin: 5 Parts 5578 Part A + 1 Part 5735 Part B (5A:1B), MIROTHANE PU 5747 may also be used in Matt. Pot Life : Up to 24 hours at 25°C Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin 30% with MIROSOL 1217 (Fast), 1266 (Slow), 1218 (Ultra Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior: Reconstituted, dyed and natural wood veneers, joinery, kitchen cupboards, wardrobes, wall panelling, furniture-table topcoat, bench tops, commercial furniture and fit-outs, window furnishings and blinds. Read More
MIROTHANE PU 5577 Sun Shield Clear Topcoat-image
MIROTHANE PU 5577 Sun Shield Clear Topcoat
Code: 5577 High-performance, clear, two-pack, non-yellowing, acrylic polyurethane for interior wood & wood composites. MIROTHANE PU 5577 Sun-Shield contains a sophisticated package of UV absorbers and light stabilisers that have been proven highly effective in protecting reconstituted, dyed and natural wood veneers from colour change when exposed to ultraviolet (UV) light. Features: Contains UV absorbers and light stabilisers that have been proven highly effective in protecting reconstituted, dyes and natural wood veneers from colour change when exposed to ultraviolet (UV) light. High solids means less coats are required to achieve a full finish Subdued gloss is highly resistant to unsightly oily finger prints. Fingerprints can be easily removed with a clean rag without leaving residual gloss spots, particularly important when applying a clear matt topcoat over a dark base Available in a full range of gloss levels; matt, satin, semi-gloss and full gloss Specifications: Colour : Clear Finish : Matt (10%), Satin (30%), Semi Gloss (60%) & Full Gloss Build : Very Good Sandability : Good Vertical Hold Up : Good Solvent Resistance : Very Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1208 or 1234 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Matt & Satin: 4 Parts 5577 Part A + 1 Part 5735 Part B (4A:1B) Full Gloss: 4 Parts 5577 Part A + 1 Part 5757 or 5789 (4A:1B) Pot Life : Up to 8 hours at 25°C Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Matt & Satin: Thin 40-60% with MIROSOL 1217 (Fast), 1263 (Medium), 1266 (Slow), 1218 (Ultra Slow) Full Gloss: Thin up to 15% with MIROSOL 1263 (Medium), 1266 or 1260 (Slow), 1218 (Ultra Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior: Reconstituted, dyed and natural wood veneers, kitchen cupboards, wall panelling, table topcoat, bench tops, commercial furniture and fit-outs, window furnishings and blinds, children’s toys. Semi Exterior: Covered entry doors and internal faces of opening windows. Exterior: When used as a protective clear topcoat over an exterior grade pigmented basecoat e.g. MIROTHANE PU 5610 polyurethane on metal, plastic or over appropriately primed carbon fibre. Read More
MIROTHANE PU 5555 Clear Topcoat-image
MIROTHANE PU 5555 Clear Topcoat
Code: 5555 Premium, two pack, clear polyurethane. High clarity results in striking grain definition and enhances the natural beauty of stained timber. Features: Excellent water and chemical resistance makes it ideal for demanding in-service environment  such as marine fit-outs, bench tops and bar tops Very low yellowing, it is suitable for use over light coloured wood and veneers when mixed with a low yellowing MIROTHANE PU Part B Hardener The full gloss version results in a brilliant high gloss finish with excellent distinction of image (DOI). Available in satin, semi gloss and full gloss Specifications: Colour : Clear Finish : Satin (30%), Semi Gloss (60%) & Full Gloss Build : Very Good Sandability : Excellent Vertical Hold Up : Good: Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : Refer to datasheet for mixing ratios Pot Life : 2-3 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Refer to datasheet for thinning Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for demanding environments such as bar, kitchen bench tops, bathroom vanities, interior marine fit-outs and commercial fit outs. Read More
MIROTHANE PU 5545 Clear Sealer-image
MIROTHANE PU 5545 Clear Sealer
Code: 5545 Premium, two pack, clear, polyurethane sealer that provides an excellent sanding base for clear polyurethane topcoats. Features: Good build enhances the final finish by sealing, filling and covering the fibres of the the substrate Excellent flow and levelling Easy sanding ensures time to sand and the best possible surface tor topcoating Low yellowing, suitable over light coloured wood/veneers and liming stains when mixed with one of the low yellowing MIROTHANE Part B Hardeners Specifications: Colour : Milky in can dries clear Build : Very Good Sandability : Excellent Vertical Hold Up : Good Solvent Resistance : Very Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : 2 Parts 5545 Part A + 1 Part 5747 Part B (2A:1B) or 4 Parts 5545 Part A + 1 Part 5715, 5728, 5735 or 5757 (4A:1B) Pot Life : 2-3 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin 10-20% with MIROSOL 1217 (Fast), 1263 (Medium), 1266 or 1218 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Commercial joinery, wall panelling, domestic furniture, high rise office and hotel fit outs and interior marine fit-outs. Read More
MIROTHANE PU 5789 Ultra Flex High Solids Hardener-image
MIROTHANE PU 5789 Ultra Flex High Solids Hardener
Code: 5789 To View Tech Data Sheet and Safety Data Sheet: Register To View Read More
MIROTHANE PU 5780 Slow Hardener-image
MIROTHANE PU 5780 Slow Hardener
Code: 5780 To View Tech Data Sheet and Safety Data Sheet: Register To View Read More
MIROTHANE PU 5757 Medium High Solids Hardener-image
MIROTHANE PU 5757 Medium High Solids Hardener
Code: 5757 To View Tech Data Sheet and Safety Data Sheet: Register To View Read More
MIROTHANE PU 5747 Fast Hardener-image
MIROTHANE PU 5747 Fast Hardener
Code: 5747 To View Tech Data Sheet and Safety Data Sheet: Register To View Read More
MIROTHANE PU 5735 Fast/Med High Solids Hardener-image
MIROTHANE PU 5735 Fast/Med High Solids Hardener
Code: 5735 To View Tech Data Sheet and Safety Data Sheet: Register To View Read More
MIROTHANE PU 5728 Fast Cure High Solids Hardener-image
MIROTHANE PU 5728 Fast Cure High Solids Hardener
Code: 5728 To View Tech Data Sheet and Safety Data Sheet: Register To View Read More
MIROTHANE PU 5535 Clear Sealer-image
MIROTHANE PU 5535 Clear Sealer
Code: 5535 A two pack, clear, polyurethane sanding sealer typically used under MIROPOL PE 5007 High Gloss Clear Top Coat on timber, veneer or foil covered MDF board to provide a high-gloss, wet look finish. Features: Fast drying and easy sanding Excellent flow & levelling Highlights the grain and colour of Rimu Can be used under any Mirotone clear topcoat Specifications: Build: Very Good Sandability: Very Good Vertical Hold Up: Excellent Solvent Resistance: Very Good Water Resistance: Excellent Levelling & Flow: Excellent Sink Back: Minimal Colour: Milky in-can dries clear To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio: 2 Parts 5535 Part A + 1 Part 5730 Part B Pot Life: 3-4 hours at 25ºC   (Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning: Not normally required but can be thinned up to 5% with MIROSOL 1217 Fast Thinner if required. Suction Gun: Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot: Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400 kpa (50-55 psi) and a pot pressure of 45 kpa (6psi) max. Airless Spray - Use 0.23 to 0.33 (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400 kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90 kpa (10-15psi). Where To Use: Interior use only for example solid and veneer timber fixtures and furniture including restaurant, bar and hotel furniture, pianos and caskets. Read More
MIROTHANE PU 5500 Isolator-image
MIROTHANE PU 5500 Isolator
Code: 5500 Versatile clear isolator that minimises the risk of resin exudation and tannin bleed on timber and minimises the risk of edge cracking on MDF. Features: Fast drying No sanding required Water white, excellent clarity Excellent adhesion to wood, MDF & LPM Specifications: Colour : Clear Build : Low Vertical Hold Up : Good Solvent Resistance : Good Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 10m2 per litre at 100 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : When used as a two pack mix 10 Parts 5500 Part A + 1 Part 5789 (10A:1B). Pot Life : 4 hours at 25°C Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin single pack 20-30% and two pack 12-25% with MIROSOL 1217 (Fast), 1263 (Medium), 1266 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Tannin blocking primer under MIROTEC WB water based coatings, mouldings, picture frames, MDF furniture and fixtures, MDF routed grooves and solid Jarrah furniture and articles. Read More
MIROTHANE PU 5631 White Undercoat-image
MIROTHANE PU 5631 White Undercoat
Code: 5631 Premium, high build, two pack polyurethane undercoat. Features: Fast drying, ideal for automatic lines with in-line or early forced drying Easy to sand, powders easily making it ideal for hand sanding Has a slight sheen making it easier to see where it has been sanded Low sink back, produces and excellent high gloss finish when topcoated with one of Mirotone’s full gloss polyurethane topcoats, comparable with the gloss achieved with a polyester undercoat Excellent vertical hold up Specifications: Colour : White & Tinted Finish : Slight sheen Build : Very High Sandability : Excellent Vertical Hold Up : Excellent Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated. Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : 2 Parts 5631 Part A + 1 Part 5747 Part B (2A:1B) or 4 Parts 5631 Part A + 1 Part 5728 or 5735 (4A:1B) Pot Life : 2 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin up to 40% with MIROSOL 1217 (Fast), 1263 (Medium) or 1218, 1266 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use. Interior doors, kitchen & bathroom cabinets, commercial joinery, wall panelling and domestic furniture. Read More
MIROTHANE PU 5626 White Undercoat-image
MIROTHANE PU 5626 White Undercoat
Code: 5626 Premium grade, high solids, low viscosity two pack polyurethane undercoat. Very easy to sand and provides excellent DOI (Distinction of Image) when topcoated with a MIROTHANE PU topcoat gloss. Features: Easy to sand, powders easily making it ideal for hand sanding High solids, low viscosity provides superior build with minimal thinning. Excellent for sealing the fibres of MDF. Superior chemical and moisture resistance Use up excess MIROTHANE PU 5650  topcoat by adding it into MIROTHANE PU 5626 to create your own tinted undercoat Specifications: Colour : White, Black & Tinted Build : Very High Sandability : Excellent Vertical Hold Up : Excellent Solvent Resistance : Excellent Water Resistance : Excellent Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6-7m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ration (by volume) : 3 Parts 5626 Part A + 1 Part 5747 Part B (3A:1B) or 5 Parts 5626 Part A + 1 Part 5715, 5728 or 5735 (5A:1B) Pot Life : 2 hours at 25°C Pot life varies significantly with ambient temperature, humdity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin up to 20% with MIROSOL 1217 (Fast), 1263 (Medium), 1218, 1266 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use. Doors, kitchen & bathroom cabinets, commercial joinery and wall panelling and domestic furniture. Read More
>