Code: 4925 A biodegradable paint remover designed to remove old and/or weathered coatings from sound exterior timber surfaces. Features: No strong caustic chemicals Removes coating without adversely affecting the underlying timber Will remove most conventional coatings Coverage : 2.5 m² per litre Clean Up : Water Packaging : 1L, 4L, 10L & 15L To View Tech Data Sheet and Safety Data Sheet: Register To View Precautions : Do not use QSTRIP on plastic surfaces. Do not use if rain is forecast. Do not allow to dry out. Product works most efficiently between 15-25°C. Avoid applying in conditions of prolonged full sun. Applications : Good preparation is key to a professional looking, long lasting finish. Remove any loose or peeling paint and obvious solid soil or dusty agglomerates. Wet Test a small area prior to application to determine the thickness (generally 3mm) of QSTRIP required and note the time (minimum 40 minutes) needed to allow it to work Apply using a brush, roller or applicator pad, and leave QSTRIP for a minimum of 40 minutes to soften and dissolve the film. Thicker coatings may take a few hours. It is advisable to check a small area with a palette knife. If it removes easily proceed with the entire area. On stubborn coatings use a stiff broom or brush, (pay close attention to cracks and grooves), then remove by scraping, scrubbing or power wash. Generally, two applications will work, however sometimes a third application may be required. Leave to dry and examine. Repeat process in any areas that have not been removed until the entire area is acceptable. Designed for timber but may be applied to glass, metal, concrete, plaster or masonry. (Refer to technical for more information). Read More

Code: 4910 POWER CLEAN oil and sealer remover is ideal for removing oil treatments, sealers and weathered oil based finishes from external timber surfaces. Apply undiluted POWER CLEAN to a wet surface using a garden spray, brush or roller (no thinning is required). Features: Removes weathered oil based finishes, stains, treatments and sealers in as little as 10 minutes Apply on any exterior timber surface Coverage : Approx. 10m² per litre Clean Up : Water Packaging : 4L & 10L To View Tech Data Sheet and Safety Data Sheet: Register To View Note: Failure to thoroughly remove the cleaning solution may result in timber discolouration under clear finishes. Application : Wet surrounding areas and plants before starting. Apply undiluted POWER CLEAN to wet surface using a garden spray, brush or roller. (No thinning required). Allow POWER CLEAN to remain wet on the surface for approximately 10 minutes. (Do not let the product dry on the surface). Using a stiff bristle broom, scrub the surface to see if the coating has lifted. Use a strong jet of water or pressure wash to rinse the surface of the timber. Repeat if necessary. Follow up with DEX PREP to neutralise the timber and rid the surface of any darkening which may occur in the cleaning process. (1L DEX PREP : 1L Water). All exterior timber surfaces. Read More

Code: 4915 A biodegradable, non toxic timber cleaner for removing tannins and extractives. Features: Remove tannins and extractives Remove mill glaze to allow penetration of the coating Do not have to wait for to timber to weather before applying coatings Coverage : 300g conatiner will clean approximately 25-30m² of decking and 50m² of vertical surfaces. Clean Up : Water Packaging : 300g or 900g To View Tech Data Sheet and Safety Data Sheet: Register To View SAP STRIP is essential for use on all timbers under 12 months old where full weathering hasn't occurred. Note - Mill glaze is a term used when the planers or blades in the dressing process close the top cells of the timber, this gives the timber a polished look. Application : Dissolve 300g in 5 litres of hot water (for vertical surfaces dissolve 300g in 10 litres of hot water). Apply with a brush or garden spray. Agitate with a stiff broom or brush to bring tannins and extractives to the surface. Leave for 15-30 minutes. Wash off with a strong jet of water (preferably a power wash) to rid the surface of any residual cleaner and tannins brought to the surface. All timber under 12 months where full weathering hasn't yet occured. Read More

Code: 4930 A timber brightener that cleans and brightens weathered and grey timber and assists in opening the timber grain to allow penetration of the coating. Features: Highly concentrated Used neat it will kill mould spores Coverage : 6-8m² per litre Drying : Oil based paint or stains : 2 to 3 days. Water based paints or stains : As soon as timber is dry. Clean Up : Water Packaging : 1L, 4L & 10L To View Tech Data Sheet and Safety Data Sheet: Register To View Do not "Spot Clean" as this may result in a patchy appearance  Clean the whole area at the same time. DEX PREP may not remove old deep seated fungal stains and timber marking dyes. For best results apply DEX PREP to cool surfaces out of direct sunlight. Do not allow to dry on the surface before removal. Failure to remove the cleaning solution residue may result in timber discolouration under clear finishes or early failure of the coating due to changed pH. DEX PREP is mildly acidic, avoid contact with painted metal surfaces and vegetation. Rinse thoroughly if contact occurs. Application : Remove surface dirt by sweeping or hosing. Shake DEX PREP thoroughly and mix in a plastic container or bucket. General Cleaning: Mix one part DEX PREP to 5 parts water Severe Staining: Apply neat. Wet the surface to be cleaned. Apply mixture generously with a scouring or scrubbing brush and scrub timber thoroughly. Leave for 10-15 minutes. Rinse off using a garden hose, or high pressure water cleaner for large area or badly discoloured timber. Grey or dirty timber over 12 months old. Read More