MIROLAC NC Nitrocellulose & MIROCAT PC Pre-Catalysed Lacquers

Code: 3220 Premium quality, high build, single pack, pre-catalysed clear lacquer. Features: High solids content provides improved hold up for better overall appearance and reduces the number of coats required Easy to use, achieve an excellent finish with minimal effort Formulated on a very clear, low yellowing resin  and contains UV absorbers to ensure maximum protection of the substrate from UV light High in can viscosity allows the applicator to adjust the coating viscosity to suit their requirememts Good clarity, provide good grain definition and depth of colour Excellent flow and levelling results in a smooth even finish Specifications: Colour : Clear Finish : Matt (10%), Satin (30%), Semi Gloss (60%) & Full Gloss Build : High Sandability : Excellent Vertical Hold Up : Good Solvent Resistance : Good Water Resistance : Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application:  Thinning Subdued Gloss : Thin up to 30% with MIROSOL 1222 or 1220 (Fast), 1294 (Medium), 1242 (Slow) Thinning Full Gloss : Thin 20-30% with MIROSOL 1222 or 1220 (Fast), 1294 (Medium), 1242 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Hot Spray - Temperature guide 35-40°C. Where To Use: Interior use only. Ideal for domestic furniture, children's toys and furniture, picture frames, musical instruments, joinery and antique restoration Read More

Code: 3210 User friendly, single pack, pre-catalysed clear lacquer for fixture and furniture finishing. Features: Easy to use, achieve an excellent finish with minimal effort Ready for use (RFU), no thinning required, apply directly from the can Good clarity, provide good grain definition and depth of colour Excellent flow and levelling results in a smooth even finish Specifications: Colour : Clear Finish : Satin (30%) & Semi Gloss (60%) Build : High Sandability : Excellent Vertical Hold Up : Good Solvent Resistance : Good Water Resistance : Good Levelling & Flow : Good Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated. Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Thinning : Thin up to 10% with MIROSOL 1222 or 1220 (Fast), 1294 (Medium), 1242 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for domestic furniture, children's toys and furniture, picture frames, musical instruments, joinery and antique restoration Read More

Code: 3150 User friendly, single pack, pigmented topcoat ideal for furniture and fixtures. It´s easy to apply, fast drying and results in a velvet smooth high build finish Features: Easy to use to achieve an excellent finish with minimal effort or expertise Excellent build reduces the number of topcoats required Single pack, no pot life issues to manage Formaldehyde free, safer for the applicator, zero formaldehyde emissions in rooms in which articles are  installed Phthalate free, ideal for children’s toys and furniture Specifications: Colour : White, matched to colour on request Finish : Matt (10%), Satin (30%), Semi Gloss (60%) & Full Gloss Build : Good Sandability : Good Vertical Hold Up : Good Solvent Resistance : Good Water Resistance : Good Levelling & Flow : Very Good Sink Back : Minimal Coverage : 8m2 per litre at 125 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Thinning : Thin 10-20% with MIROSOL 1222 or 1220 (Fast), 1294 (Medium), 1242 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for domestic furniture, internal doors, children’s toys and furniture and built in wardrobes. Read More

Code: 3241 An economical, fast drying, easy to sand clear sealer. Can be applied over dark timbers or stains enhancing the natural colours without clouding the finished appearance. Features: High build provides improved hold up and reduces the number of coats required Easy to use, achieve an excellent finish with minimal effort Fast drying allows early sanding which minimises production time Specifications: Colour : Turbid in can, dries clear Build : High Sandability : Excellent Vertical Hold Up : Very Good Solvent Resistance : Good Water Resistance : Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Thinning : Thin up to 10% with MIROSOL 1222 or 1220 (Fast), 1294 (Medium), 1242 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for domestic furniture, children’s toys and furniture, picture frames, musical instruments, joinery and antique restoration. Read More

Code: 3244 High build, single pack, clear pre-catalysed sanding sealer provides an excellent base for a range of Mirotone topcoats. Features: High build provides improved hold up and reduces the number of coats required Easy to use, achieve an excellent finish with minimal effort May be catalysed with MIROBILD AC 3800 Universal catalyst to improve chemical resistance when using as a sealer under acid-catalysed and polyurethane topcoats Fast drying allows early sanding which minimises production time Specifications: Colour : Milky in can, dries clear Build : High Sandability : Excellent Vertical Hold Up : Very Good Solvent Resistance : Good Water Resistance : Good Levelling & Flow : Excellent Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Mixing Ratio (by volume) : To improve the water and chemical resistance of the coating system, add 20ml of MIROBILD AC 3800 Catalyst to every litre of MIROCAT PC 3244 and then add thinner. Apply catalysed coating within two days of adding catalyst. Pot Life : 2 days at 25°C Pot life varies significantly with ambient temperature, humidity and the quantity mixed. Pot life is longer at lower temperatures and shorter at higher temperatures. The larger the quantity mixed, the shorter the pot life will be. Only mix the quantity required for the job. Thinning : Thin 15-30% with MIROSOL 1222 or 1220 (Fast), 1294 (Medium), 1242 (Slow) Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for domestic furniture, children’s toys and furniture, picture frames, musical instruments, joinery and antique restoration. When catalysed and top coated with MIROBILD AC topcoats or MIROTHANE PU 5588 Clear Topcoat may be used on kitchen cabinets and commercial furniture. Read More

Code: 3130 A user friendly, single pack, pigmented undercoat for internal wood and medium density fireboard (MDF). It is fast drying with excellent sanding properties. Features: Easy to sand, powders easily reducing sanding time Fast drying enables increased production throughput Minimises the risk of wax extraction when applied over MDF and HDF Single pack, no pot life issues to manage Formaldehyde free. safer for the applicator, zero formaldehyde emissions in rooms in which articles are installed Use up left over MIROLAC NC 3150 topcoat by adding MIROLAC NC 3130 to create your own tinted undercoats Specifications: Colour : White Build : Good Sandability : Good Vertical Hold Up : Good Solvent Resistance : Good Water Resistance : Good Levelling & Flow : Very Good Sink Back : Minimal Coverage : 6m2 per litre at 150 micron wet film build. This is dependent on the application equipment / gun set up and the article being coated Dry Time : Refer to Technical Data Sheet Clean Up : Clean all equipment using MIROSOL 1222 or 1286 Thinner To View Tech Data Sheet and Safety Data Sheet: Register To View Application: Thinning: Thin 25-40% with MIROSOL 1222 or 1220 (Fast), 1294 (Medium), 1242 (Slow). Suction Gun - Use 1.5 to 2mm (59-79 thou) orifice with 350-400kpa (50-55 psi). Pressure Pot - Use 1.5 to 2mm (59-79 thou) orifice with pressure pot air-cap. Gun pressure 350-400kpa (50-55 psi) and a pot pressure of 45kpa (6 psi) max. Airless Spray - Use 0.23 to 0.33mm (9-13 thou) orifice, 15cm fan (dependent on job) with regulated pump pressure of 350-400kpa (50-55 psi). Air Mix Guns - Settings similar to airless spray with the air-assisted regulator pressure at 70-90kpa (10-15psi). Where To Use: Interior use only. Ideal for domestic furniture, internal doors, children’s toys and furniture and built in wardrobes. Read More